Yngvar Berg

• Mirmotahari, Omid & Berg, Yngvar (2026). Students judge different things differently: dimension-specific self-assessment calibration in introductory digital circuit design. Computer Science Education. ISSN 0899-3408. s. 1–20. doi: 10.1080/08993408.2026.2705528. Fulltekst i vitenarkiv
• Mirmotahari, Omid; Grun, Helene Nordrum & Berg, Yngvar (2025). Gamification as a transferable pedagogical innovation for technology education: developing 21st-century skills through collaborative game-based learning. Frontiers in Education. 10. doi: 10.3389/feduc.2025.1684459. Fulltekst i vitenarkiv Vis sammendrag

  Introduction: Technology literacy has become essential across all academic disciplines, yet traditional pedagogical approaches often struggle to engage students while simultaneously developing twenty-first-century collaborative competencies. This study investigates gamification as an innovative pedagogical method for technology education, examining its effectiveness in developing technology awareness, digital literacy, and collaborative skills. Methods: We conducted a case study of two pilot implementations in an introductory computer science course (n = 117 students across two cohorts). The intervention consisted of a narrative 10 driven, collaborative game-based learning track offered alongside a traditional course format. We employed mixed-methods analysis to assess student engagement, motivation, technology comprehension, and learning outcomes. Participation in the gamified track was voluntary and cohorts were not randomized. Results: The gamified approach achieved 100% completion rates in the first pilot and 88–92% satisfaction rates across both implementations. Participation in the gamified track was associated with higher reported motivation and collaborative skill development compared to the traditional track. In the second pilot, students who chose the gamified track achieved higher exam scores than peers in the traditional track; however, due to voluntary participation and non-randomized cohorts, these differences represent associations rather than causal effects. Platform consistency emerged as a critical factor: when bonus tasks required platform switching, completion rates significantly dropped across three chapters, indicating that integrated digital learning environments are essential for managing cognitive load and optimizing learning outcomes. Discussion: These findings demonstrate that gamification can effectively teach technology concepts through game mechanics whilst simultaneously developing collaborative competencies. We propose a transferable framework for implementing gamification in technology education across disciplines. This research contributes to understanding how innovative pedagogical approaches can address the growing need for technology literacy in higher education.

• Lauvås, Per; Mirmotahari, Omid; Sandtrø, Tengel Aas; Berg, Yngvar & Lindsjørn, Yngve (2025). Gradert karakterskala eller Bestått/Ikke bestått? Refleksjoner fra studenter i høyere IT utdanning. NIKT: Norsk IKT-konferanse for forskning og utdanning. ISSN 1892-0713. 37(4). doi: https:/www.ntnu.no/ojs/index.php/nikt/article/view/6554. Fulltekst i vitenarkiv Vis sammendrag

  Denne studien undersøker IT-studenters oppfatninger om karak-teruttrykkene gradert karakterskala (A–F) versus Bestått/Ikke bestått (B/IB) inorsk høyere utdanning, et tema som har fått økt aktualitet etter at flere presti-sjeutdanninger nylig har vedtatt overgang til B/IB-vurdering. Gjennom kvalitati-ve fokusgruppeintervjuer med 34 studenter fra tre utdanningsinstitusjoner iden-tifiserer studien en preferanse for gradert skala blant IT-studenter. Denne prefe-ransen tilskrives primært karakterers innvirkning på akademisk motivasjon, kon-kret tilbakemelding på mestringsnivå, samt oppfattet merittverdi for framtidigkarriere og videre studier. Samtidig avdekker funnene noen mulige fordeler vedB/IB, herunder redusert akademisk stress og økt potensial for interessedrevet læ-ring framfor karakterjag. Egnethet for karakteruttrykk kan også være domene-og kontekstavhengig. Forskningsresultatene utgjør et empirisk fundament for in-dividuelle og institusjonelle beslutninger om valg av karakteruttrykk innen in-formasjonsteknologiutdanning og bidrar til den pågående debatten om valg avkarakteruttrykk i høyere utdanning.

• Berg, Yngvar & Mirmotahari, Omid (2025). Hvorfor deltar ikke studentene på gruppeundervisning? Nordic Journal of STEM Education. 9(2), s. 79–82. doi: 10.5324/njsteme.v9i2.6403. Fulltekst i vitenarkiv Vis sammendrag

  Det er ingen tvil om at aktiv læring i små grupper kan være et svært viktig for læringsutbytte, spesielt for nye studenter i første semester. En omfattende undersøkelse er gjennomført for å identifisere årsaker til lav studentdeltakelse og for å evaluere studentenes opplevelse av undervisningskvalitet. Formålet er å foreslå konkrete tiltak for kvalitetsheving, med fokus på de underliggende årsakene til manglende deltakelse. Tiltakene er spesielt relevante for emnet IN1020, men er også generelt nyttige for emner med gruppeundevisning i høyere utdanning. Basert på de omfattende tilbakemeldingene fra studentene, foreslås det betydelige endringer i organiseringen av gruppetimer og ulike tiltak for å forbedre kvaliteten. Et av de mest fremtredende forslagene er å benytte to læringsasistenter (gruppelærere) per gruppeundervisning. Fordelene med dette tiltaket inkluderer forbedret undervisningskvalitet, økt studentdeltakelse, og en generell forbedring av studentenes læringsopplevelse som vil kunne føre til vesentlig bedre læringsutbytte. Vi identifiserer studentenes forventninger og behov, og foreslår tiltak for å gjøre undervisningen mer engasjerende og tilgjengelig. Artikkelen avsluttes med en diskusjon om hvordan gruppeundervisningen kan utvikles videre for å møte studentenes behov og styrke læringsmiljøet, samtidig som vi argumenterer for at en mer fleksibel og studenttilpasset tilnærming kan bidra til økt deltakelse og bedre læringsutbytte i høyere utdanning.

• Mirmotahari, Omid; Mørch, Anders & Berg, Yngvar (2024). Evolution of Technological Innovations, User Experiences, and Literacies. CEUR Workshop Proceedings. 3685. Fulltekst i vitenarkiv Vis sammendrag

  The advancement of computer-based innovations over the years has drastically altered the role of the end-user, from passive users of technology to active participants influencing technological development. Each major innovation, associated with preceding hardware and software milestones, has led to new understandings and skill sets required of end-users. This workshop position paper explores the technological progress from mainframe computers to personal computers, the internet, and the nascent age of artificial intelligence (AI) based on Large Language Models (LLMs). We examine how each technological leap has transformed the end-user experience, the evolving literacies demanded, and speculate how the evolution of user interaction with technology in the future might move in different directions and widen the technological gap.

• Mirmotahari, Omid & Berg, Yngvar (2024). Trenger vi læringsassistenter? Hvordan kan hverandre-vurdering og/eller egen-vurdering gi god læringsutbytte. NIKT: Norsk IKT-konferanse for forskning og utdanning. ISSN 1892-0713. 4. doi: 10.5324/nikt.6234. Fulltekst i vitenarkiv Vis sammendrag

  Denne studien undersøkes effekten av lærerassistentvurdering (LV),egenvurdering (EV) og hverandrevurdering (HV) på læringsutbyttet til 528 studenter i et introduksjonskurs i informatikk. Studentene ble tilfeldig fordelt i tregrupper, hvor hver gruppe mottok en annen type tilbakemelding på en obliga-torisk oppgave. Resultatene viste at alle intervensjonene førte til en signifikantforbedring i studentenes prestasjoner fra første utkast til endelig innlevering (p

• Mirmotahari, Omid; Islam, Md Rifat Naim; Berg, Yngvar; Foss, Camilla & Stensland, Håkon Kvale (2023). Spillifisering for økt engasjement, fleksibilitet og alternativt læringsløp. NIKT: Norsk IKT-konferanse for forskning og utdanning. ISSN 1892-0713. Fulltekst i vitenarkiv
• Mirmotahari, Omid & Berg, Yngvar (2023). Utvikling av førsteårsstudenters tilbakemeldingskompetanse gjennom egen-vurdering. NIKT: Norsk IKT-konferanse for forskning og utdanning. ISSN 1892-0713. Fulltekst i vitenarkiv
• Azadmehr, Mehdi; Marchetti, Luca & Berg, Yngvar (2021). An analog voltage similarity circuit with a bell-shaped power consumption. Electronics (Basel). 10(10). doi: 10.3390/electronics10101141. Fulltekst i vitenarkiv Vis sammendrag

  This paper presents a voltage similarity circuit (bump circuit) based on a novel voltage correlator. The proposed circuit is characterized by a power consumption which depends on the similarity between the two inputs. The sensitivity of the bump circuit and the power consumption are at the highest values when the inputs are equal. As the similarity between the input voltages decreases, the total current consumption decreases with a bell-shaped behavior. The proposed bump circuit is very simple in design, made of a new voltage correlator circuit in combination with a differential pair and mimics the behavior of the classical bump circuit. The voltage correlator was implemented using AMS−350nm CMOS technology. Simulation and measurement results suggests that a low power consumption may be achieved if the circuit is used in applications where the input signals have large dissimilarity for most of the circuit operation

• Azadmehr, Mehdi; Schreyer-Miller, Aaron; Paprotny, Igor & Berg, Yngvar (2019). A New Differential Oscillator with T-type Feedback. I Chakrabarti, Satyajit & Saha, Himadri Nath (Red.), 2018 9th IEEE Annual Ubiquitous Computing, Electronics & Mobile Communication Conference (UEMCON): 8th-10th November, 2018. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781538676936. s. 779–782. doi: 10.1109/UEMCON.2018.8796794. Fulltekst i vitenarkiv
• Mirmotahari, Omid; Berg, Yngvar; Gjessing, Stein; Fremstad, Ester & Damsa, Crina I. (2019). A Case-Study of Automated Feedback Assessment. IEEE Global Engineering Education Conference, EDUCON. ISSN 2165-9559. April-2019, s. 1190–1197. doi: 10.1109/EDUCON.2019.8725249. Fulltekst i vitenarkiv Vis sammendrag

  This study was conducted in a first year university course in computer programming. We investigated how the use of a digital assessment tool, consisting of quantitative weighting and which simultaneously generate qualitative formative feedback, improves the quality of the assessment and not least supports the students' further learning. Analysis of quantitative data generated by the digital system, as well as qualitative data from involved parties, shows clear improvements in validity and reliability in assessment. All students received automated feedback on their exam. In this paper, we show how the use if the tool contributed to students' learning and academical development. Furthermore, we present the process of developing this system for evaluation and automatic feedback, and conclude with results seen from teachers, reviewers and students' perspectives.

• Azadmehr, Mehdi; Paprotny, Igor & Berg, Yngvar (2019). Q-Loading of Colpitts-Based Mass-Sensing Oscillators in Resonator-based MEMS Airborne Particulate Matter (PM) Sensors. IEEE International Symposium on Consumer Electronics. ISSN 2158-3994. doi: 10.1109/ICCE.2019.8662115. Fulltekst i vitenarkiv
• Marchetti, Luca; Azadmehr, Mehdi & Berg, Yngvar (2019). A bidirectional front-end for discrete resonating transducers based on a non ring oscillator, 16th International Conference on Electrical Engineering/Electronics, Computer, Telecommunications and Information Technology (ECTI-CON). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781728133614. s. 242–245. doi: 10.1109/ECTI-CON47248.2019.8955216. Fulltekst i vitenarkiv
• Mirmotahari, Omid; Berg, Yngvar; Fremstad, Ester & Damsa, Crina I. (2019). Student engagement by employing student peer reviews with criteria-based assessment. IEEE Global Engineering Education Conference, EDUCON. ISSN 2165-9559. April-2019, s. 1152–1157. doi: 10.1109/EDUCON.2019.8725174. Fulltekst i vitenarkiv Vis sammendrag

  Evaluation of student projects by students themselves is highlighted in research as a method to engage the students, and to strengthen their learning and meta-cognition. Assessing others students' achievements can be a way for beginner students to develop insight into the academic criteria and methods in a subject. It can also contribute to their understanding of their own learning process and how they best can make progress with the studies. We used the Canvas functions Rubrics and SpeedGrader to manage a review of 524 student projects. We examined various aspects: how the students experienced this type of learning activity; whether the students' assessments were in line with the teachers' review; in what way and to what extent reviewing each others' work contributed to their learning; and how data generated through this activity provides information to teachers to improve their teaching. Despite some technical shortcomings and challenges, the experiment generated a series of insightful results.

• Azadmehr, Mehdi; Paprotny, Igor & Berg, Yngvar (2018). A Differential Complementary Colpitts Oscillator based on Common Drain Topology. I Ao, S. I.; Douglas, Craig & Grundfest, Warren S. (Red.), Proceedings of the World Congress on Engineering and Computer Science 2018. International Conference on Circuits and Systems (ICCS 18). 23-25 October, 2018, San Francisco, USA. Vol I. Newswood Limited. ISSN 9789881404817. s. 20–23. Fulltekst i vitenarkiv
• Marchetti, Luca; Berg, Yngvar & Azadmehr, Mehdi (2018). A bidirectional front-end for ultrasonic pulse-echo measurements, 2018 IEEE 15th International Conference on Networking, Sensing and Control (ICNSC). March 27-29, Zhuhai, China. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781538650530. doi: 10.1109/ICNSC.2018.8361284. Fulltekst i vitenarkiv
• Marchetti, Luca; Berg, Yngvar & Azadmehr, Mehdi (2018). A Compact Bidirectional Pseudo Floating Gate Front-End for Resonating Sensors based on NAND and NOR logic Gates, 2018 IEEE International Conference on Semiconductor Electronics (ICSE2018): Proceedings: 15 – 17 August 2018 Pullman Kuala Lumpur City Centre Hotel & Residence, Kuala Lumpur, Malaysia. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781538652831. s. 221–225. doi: 10.1109/SMELEC.2018.8481284. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present an alternative method to realize a compact bidirectional Front-End for resonating sensors based on Ring Down Method (RDM) and pseudo floating gate amplifier (PFGA). This goal is achieved by using the voltage buffer inside the PFGA for both biasing of the amplifier and actuation of the sensor. The proposed analog front-end doesn't require any coupling capacitor, minimizing the area occupied by the circuit. Simulations in AMS-350nm CMOS technology with a power supply of 3.3V and measurements on a prototype implemented with discrete components have been used to verify the correct operation of the system. The Front-end was realized by using the integrated circuits (ICs) CD4007UBE and ALD1103, and tested with a real piezoelectric transducer (MURATA MA40S4R), characterized by a resonant frequency of 40kHz. Measurement and simulation results show that the proposed circuit is a good candidate to realize a compact and bidirectional pseudo floating gate front-end, which resembles the circuit of NAND and NOR logic gates.

• Marchetti, Luca; Berg, Yngvar & Azadmehr, Mehdi (2018). A self-cascode pseudo floating gate front-end for resonating sensors, 2018 International ECTI Northern Section Conference on Electrical, Electronics, Computer and Telecommunications Engineering (ECTI-NCON 2018): Chiang Rai, Thailand 25 – 28 February 2018. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781538635537. s. 89–94. doi: 10.1109/ECTI-NCON.2018.8378288. Fulltekst i vitenarkiv Vis sammendrag

  In this work, we have demonstrated an alternative design strategy based on self-cascode transistors to improve the gain and the power consumption of a pseudo floating gate amplifier (PFGA), with the minimum area occupation. This is accomplished by implementing the inverter in the PFGA using self-cascode transistors, which provides all the advantages of a cascode amplifier (higher gain and lower power consumption), with a negligible overhead in terms of area occupation. The performance of a self-cascode pseudo floating gate amplifier (SC-PFGA) are comparable to those ones of a current-starved pseudo floating gate amplifier (CS-PFGA), with the difference that CS-PFGA requires also the circuitry to generate two reference voltages. For this reason the SC-PFGA is more compact and less power consuming than a CS-PFGA. On the other hand, the SC-PFGA doesn't provide the possibility to tune the bandwidth or the gain of the amplifier, which can be negligible in applications in which this feature is not necessary. In this work, we have compared the performance between PFGA and SC-PFGA by designing and simulating these circuits in AMS-350nm CMOS process with a power supply of 5V. This specific implementation can be applied in all those systems in which low leakage currents or voltages higher than 5V are required. In order to prove the effectiveness of this technique, the amplifier has been tested as analog front-end of a generic resonating sensor approximated with a Butterworth Van Dike model. Simulation results show that the self cascode amplifier provides a gain 7 times greater and a power consumption 12 times smaller than the ones provided by the PFGA.

• Mirmotahari, Omid; Berg, Yngvar & Damsa, Crina I. (2018). Innovating Assessment Practices Using Automated Feedback in Software in Computer Science Education. CEUR Workshop Proceedings. 2128. Fulltekst i vitenarkiv Vis sammendrag

  This study examines modalities of generating and providing automated formative feedback to Computer Science undergraduate students ’and their experiences with the system and the received feedback. A software for automated feedback has been developed and used in this study in order to both support the students learning process,and to test how a set of elaborated assessment criteria can contribute to the students better understanding of their own knowledge and learning.The findings show that providing the students with explicit feedback in addition to regular summative evaluation (grades and point sum) stimulated their understanding and awareness of their knowledge level and exam performance. Besides, it triggered ideas and reflections related to their future learning steps and approaches, which follows the principles of feed forward.

• Marchetti, Luca; Berg, Yngvar & Azadmehr, Mehdi (2018). A Discrete Implementation of a Semi-Floating Gate Amplifier for Resonating Sensor Front-End. I Napieralski, Andrzej (Red.), Proceedings of 25th International Conference Mixed Design of Integrated Circuits and Systems (MIXDES 2018): Gdynia, Poland June 21-23, 2018. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781538659113. s. 97–102. doi: 10.23919/MIXDES.2018.8443591. Fulltekst i vitenarkiv Vis sammendrag

  The growing need of electronic sensors and transducers in modern and portable applications requires to research new design methods, which aim to lower the power consumption and reduce the occupied area of the sensor interface circuitry. In this work we present the implementation of a semi-floating gate amplifier (SFGA) to realize a compact and low power resonating sensor front-end. The prototype has been fabricated by using the commercial integrated circuit CD4007UBE and tested with a power supply of 3.3V. Measurement results show that the main trade-off of this circuit is between gain and bandwidth. The maximum values recorded for these two parameters are: 150VN and 2MHz respectively. The circuit has been tested with an input sinusoidal signal and then connected to a Butterworth Van Dike (BvD) load. This type of load is commonly used to mimic the behavior of a real resonating transducer. The average current absorbed by the amplifier during the normal operation is 6μA leading to a static power consumption of 19.8μW . These values refer to a read-out frequency of 100Hz.

• Mirmotahari, Omid & Berg, Yngvar (2018). Structured peer review using a custom assessment program for electrical engineering students. IEEE Global Engineering Education Conference, EDUCON. ISSN 2165-9559. 2018-April, s. 999–1006. doi: 10.1109/EDUCON.2018.8363339. Fulltekst i vitenarkiv
• Dell’Anna, Francesco Giuseppe; Dong, Tao; Li, Ping; Wen, Yumei; Yang, Zhaochu & Casu, Mario R [Vis alle 8 forfattere av denne artikkelen] (2018). State-of-the-Art Power Management Circuits for Piezoelectric Energy Harvesters. IEEE Circuits and Systems Magazine (CAS Magazine). ISSN 1531-636X. 18(3), s. 27–48. doi: 10.1109/MCAS.2018.2849262. Fulltekst i vitenarkiv
• Marchetti, Luca; Berg, Yngvar & Azadmehr, Mehdi (2018). A Self-Actuated Front-End for Resonating Sensors, TENCON 2018 - 2018 IEEE Region 10 Conference. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781538654576. s. 559–564. doi: 10.1109/TENCON.2018.8650300. Fulltekst i vitenarkiv Vis sammendrag

  In this work, we propose a novel self-actuated analog front-end (AFE) for resonating sensors, realized in pseudo floating gate technology. The core of the analog front-end is based on a re-configurable circuit, which works as a SRAM cell when the resonating sensor must be actuated and behaves as a pseudo floating gate amplifier (PFGA) when the sensor response must be read-out. The timing for the actuation/readout cycle is provided by an inverter based control system, which is connected with the AFE in a positive feedback loop. The use of solely inverter logic gates to implement the whole system simplifies the design of the circuit, minimizes the occupied area, and makes possible to use the proposed system in low voltage applications (V DD < 3.3V). The operation of the proposed circuit has been verified by simulations in AMS-350nm CMOS technology with a power supply of 3.3V. At the end of this paper, the effects of process, temperature and power supply (PVT) variations have been investigated, and a few solutions to compensate these side effects have been proposed. Finally, the average power consumption of the circuit has been measured to be 445µW, which is in the same order of other front-ends described in literature.

• Mirmotahari, Omid; Damsa, Crina I. & Berg, Yngvar (2018). Formative Feedback for Learning. Case Studies of Automated Feedback in Undergraduate Computer Science Education. Proceedings (International Conference of the Learning Sciences). ISSN 1814-9316. 3, s. 1577–1578. Fulltekst i vitenarkiv
• Mirmotahari, Omid; Berg, Yngvar; Langmyhr, Dag; Fremstad, Ester & Damsa, Crina I. (2018). Studentaktivisering gjennom bruk av hverandrevurdering for førstesemesters studenter i Canvas LMS: en forsøksstudie. NIKT: Norsk IKT-konferanse for forskning og utdanning. ISSN 1892-0713. 1(1). Fulltekst i vitenarkiv Vis sammendrag

  I denne forsøksstudien har vi gjennomført hverandrevurdering på et førsteårsemne i informatikk. Hverandrevurdering fremheves i forskningen som en metode for å aktivisere studentene, og å styrke deres læring og metakognisjon. Ikke minst kan det å vurdere andres faglige prestasjoner være en måte for begynnerstudenter å utvikle innsikt i de faglige kriteriene og arbeidsmåtene i faget. Det kan også bidra til deres forståelse av egen læringsprosess og hvordan de best kan jobbe med studiene. Vi brukte Canvasfunksjonen Rubrics og SpeedGrader til å administrere hverandrevurdering av 524 studentbesvarelser. Det vi ønsket å undersøke var hvordan studentene erfarte denne typen læringsaktivitet; hvorvidt studentenes vurderinger var i tråd med faglærers vurdering; på hvilken måte og i hvilken grad hverandrevurderingen bidro til studentenes læring; samt hvordan data generert gjennom denne aktiviteten gir informasjon til faglærer som kunne brukes til å forbedre og tilpasse undervisningen. Til tross for enkelte tekniske mangler og utfordringer ga forsøket mange positive resultater.

• Dell’Anna, Francesco Giuseppe; Dong, Tao; Li, Ping; Yumei, Wen; Azadmehr, Mehdi & Berg, Yngvar (2018). Low-power voltage multiplier synthesis tool for preliminary topology identification, ICOSST 2017 International Conference on Open Source Systems and Technologies: Proceedings: 18-20 December, 2017 Lahore, Pakistan. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781538616581. s. 24–29. doi: 10.1109/ICOSST.2017.8279000. Fulltekst i vitenarkiv Vis sammendrag

  This paper introduces a synthesis tool designed for low-power voltage multipliers. Voltage multipliers are rectifiers employed to generate a constant output voltage, which exceeds the peak-to-peak amplitude voltage of the input signal. At low power levels the attained performance of conventional voltage multipliers is strictly related to the transistor threshold voltage in the multiplication chain, which, at low voltage levels (tens of mV), are operated primarily in the subthreshold region or in cutoff mode. To improve the power conversion efficiency of voltage multipliers at low power levels, this paper introduces a novel passive threshold compensation technique to enhance the transistor conductivity, providing a static bias voltage at the gate of the transistors. Furthermore, a CAD oriented synthesis tool for the presented threshold compensation technique is proposed. The synthesis tool gives a preliminary indication on the rectifier topology (number of stages and compensation order) given target environmental conditions, target output performance, and adopted components in the rectification chain. The core algorithm is based trial and error simulator for the simplified rectifier model, which is employed to speed up the computations pertaining the voltage multiplier synthesis.

• Schumacher, Ole Herman Elgesem; Mirmotahari, Omid & Berg, Yngvar (2018). Ultra-Low-Voltage Dual-Rail NAND/NOR for High Speed Processing, The Eleventh International Conference on Advances in Circuits, Electronics and Micro-electronics (CENICS). International Academy, Research and Industry Association (IARIA). ISSN 9781612086644. s. 1–4. Fulltekst i vitenarkiv
• Dell’Anna, Francesco Giuseppe; Dong, Tao; Li, Ping; Wen, Yumei; Azadmehr, Mehdi & Casu, Mario R [Vis alle 7 forfattere av denne artikkelen] (2018). Lower-Order Compensation Chain Threshold-Reduction Technique for Multi-Stage Voltage Multipliers. Sensors. 18(4). doi: 10.3390/s18041245. Fulltekst i vitenarkiv Vis sammendrag

  This paper presents a novel threshold-compensation technique for multi-stage voltage multipliers employed in low power applications such as passive and autonomous wireless sensing nodes (WSNs) powered by energy harvesters. The proposed threshold-reduction technique enables a topological design methodology which, through an optimum control of the trade-off among transistor conductivity and leakage losses, is aimed at maximizing the voltage conversion efficiency (VCE) for a given ac input signal and physical chip area occupation. The conducted simulations positively assert the validity of the proposed design methodology, emphasizing the exploitable design space yielded by the transistor connection scheme in the voltage multiplier chain. An experimental validation and comparison of threshold-compensation techniques was performed, adopting 2N5247 N-channel junction field effect transistors (JFETs) for the realization of the voltage multiplier prototypes. The attained measurements clearly support the effectiveness of the proposed threshold-reduction approach, which can significantly reduce the chip area occupation for a given target output performance and ac input signal

• Marchetti, Luca; Berg, Yngvar & Azadmehr, Mehdi (2018). A Low Power, High Gain Semi-Floating Gate Amplifier for Resonating Sensors Front-End. Proceedings of IEEE Computer Society Annual Symposium on VLSI, ISVLSI. ISSN 2159-3469. 2018, s. 458–463. doi: 10.1109/ISVLSI.2018.00089. Fulltekst i vitenarkiv Vis sammendrag

  In this work, we propose a low power and high gain electronic Front-end for resonating sensors based on semi-floating-gate inverting amplifiers (SFGA). Low power and high gain are achieved using a novel biasing technique of the floating gates in SFGA. The proposed amplifier has been simulated in AMS-350nm CMOS technology, characterized by very low leakages. Gain, output swing and bandwidth can be controlled by applying a proper biasing voltage. Simulation results show a trade-off between gain and bandwidth. However, the best performance recorded are: gain of 54dB (505 V/V) and bandwidth of 1.63GHz. A transient analysis with a sinusoidal input has been performed in order to verify the working principle of the SFGA. The implemented circuit provides a static power consumption of 69μW with a power supply of 3.3V. At the end of this work, the SFGA has been connected as a sensor front-end to read-out the response of a resonating sensor, which has been modelled with a Butterworth Van Dike model of a real device (MURATA MA40S4R).

• Dadashi, Ali; Berg, Yngvar & Mirmotahari, Omid (2018). Energy-efficient, fast-settling, modified nested-current-mirror, single-stage-amplifier for high-resolution LCDs in 90-nm CMOS. Analog Integrated Circuits and Signal Processing. ISSN 0925-1030. 97(2), s. 253–259. doi: 10.1007/s10470-018-1220-7. Fulltekst i vitenarkiv
• Marchetti, Luca; Berg, Yngvar & Azadmehr, Mehdi (2017). Design and modelling of a bidirectional front-end for resonating sensors based on pseudo floating gate amplifier. Electronics (Basel). 6(3). doi: 10.3390/electronics6030068. Fulltekst i vitenarkiv Vis sammendrag

  In this paper, we characterize and model a bidirectional front-end based on pseudo-floating gate amplifier (PFGA) for actuation and read-out of resonating sensors. The basic idea consists of swapping the power supply of the PFGA in order to change the directionality of the front-end. A detailed description of the system has been discussed in this paper and supported by simulations and measurement results. A prototype has been fabricated using discrete components and tested with a real transducer (Murata MA40S4) and a Butterworth Van Dyke (BvD) load, which has proved to be proved to be a well approximated model for resonant sensors. The bidirectional amplifier has been implemented with the integrated circuit CD4007UB, which is a commercial discrete component containing low leakage MOSFET. The values chosen for the BvD load are Rb = 330 W, Lm = 60 mH, Cs = 450 pF, CE = 2.2 nF, which are approximately the same values of the lumped parameters reported in the data-sheet of the real sensor. This transducer is characterized by a nominal resonant frequency of 40 kHz. Measurement results show good fitting with the models developed in this work and the possibility to predict the sensor response by using the BvD load.

• Marchetti, Luca; Berg, Yngvar & Azadmehr, Mehdi (2017). An Autozeroing Inverter Based Front-End for Resonating Sensors. I IEEE, . (Red.), 2017 12th IEEE International Conference on Design & Technology of Integrated Systems in Nanoscale Era (DTIS). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781509063772. doi: 10.1109/DTIS.2017.7930154. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we propose a new front-end for resonating sensors which is based on a logic inverter working as amplifier. The front-end is compact and auto-zeroing which makes it a good candidate for integration and for low power applications. It has been simulated in AMS-350nm CMOS Technology and a prototype has been fabricated using discrete components on a PCB. The circuit was tested with a BvD load implemented in discrete components, which can be proved to be a good model for a resonant sensor. The components used to implement the BvD load are: Lm = 3mH, Rb = 200Ω, Cs = 560pF, Ce = 3.3nF which leads to a resonant frequency of 140 KHz. The bandwidth of the amplifier is 380kHz and the mid-band gain is 55V/V. The prototype has been tested with a power supply of 5V.

• Azadmehr, Mehdi; Marchetti, Luca; Elkharashi, Moataz & Berg, Yngvar (2017). A virtual Wheatstone bridge front-end for resistive sensors. I Fortino, Giancarlo (Red.), Proceedings of the 2017 IEEE 14th International Conference on Networking, Sensing and Control (ICNSC 2017) May 16-18, 2017, Calabria, Italy. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781509044283. doi: 10.1109/ICNSC.2017.8000120. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present a novel front-end for resistive sensors based on a simple resistive voltage divider. This front-end utilizes a sampling technique to mimic the Wheatstone bridge in functionality, offers high precision and is fast at the same time more power conservative compared to the traditional Wheatstone bridge.

• Mirmotahari, Omid & Berg, Yngvar (2017). Erfaringer fra strukturert peer review ved bruk av et egetutviklet sensureringsprogram. NIKT: Norsk IKT-konferanse for forskning og utdanning. ISSN 1892-0713. 1(1). Fulltekst i vitenarkiv
• Mirmotahari, Omid & Berg, Yngvar (2017). Individuell «automagisk» tilbakemelding på skriftlig eksamen. Nordic Journal of STEM Education. 1(1), s. 287–293. doi: 10.5324/njsteme.v1i1.2327. Fulltekst i vitenarkiv Vis sammendrag

  I denne artikkelen viser vi et nytt system for å kunne gi delvis automatisk og formativ tilbakemelding til studenter på skriftlig eksamen. Vi vil belyse en ny måte å gi individuell tilbakemelding rettet mot hver enkelt students læring og fremtidige eksamensforberedelser Den faglige tilbakemeldingen er utviklet for å gi studentene større mulighet til å reflektere over egen besvarelse. Systemet er bygd opp slik at det bare medfører marginalt økt tidsbruk for sensurering ved å bruke systemet. Avslutningsvis har vi tatt med studentenes tilbakemeldinger på verdiskapningen dette systemet gir.

• Marchetti, Luca; Berg, Yngvar & Azadmehr, Mehdi (2017). A bidirectional front-end with bandwidth control for actuation and read-out of MEMS resonating sensors. I IEEE, . (Red.), 2017 MIXDES - 24th International Conference Mixed Design of Integrated Circuits and Systems: Bydgoszcz, Poland 22-24 June 2017. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781509064861. s. 185–188. doi: 10.23919/MIXDES.2017.8005180. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we propose a bidirectional front-end for resonating sensors with bandwidth control used to remove the high order oscillating modes. The electronic interface is based on an inverter working as amplifier biased by a voltage buffer, both realized in CMOS technology. The bandwidth of the amplifier can be tuned by varying a bias voltage which controls the high cut-off frequency of the front-end. A prototype was realized and tested with discrete components on a PCB. The tests were performed by using a RLC load which can be proved to be a good approximated model for a resonating sensor. The values for the load are R = 100Ω, L = 10mH, C = 270pF. Measurements were taken for Vdd=5V, Vdd=10V, Vdd=15V. Measurement results show that the bias voltage VHF affects both DC and AC characteristics of the amplifier, in particular the bandwidth varies in a range between a few kHz to a maximum of 5 MHz. A high order mode oscillation has been simulated by adding a sine wave generator at 2 MHz in series to the RLC load which was removed by filtering action of the amplifier.

• Marchetti, Luca; Berg, Yngvar; Mirmotahari, Omid & Azadmehr, Mehdi (2017). A control system for a low power bidirectional front-end for resonating sensors. I Fortino, Giancarlo (Red.), Proceedings of the 2017 IEEE 14th International Conference on Networking, Sensing and Control (ICNSC 2017) May 16-18, 2017, Calabria, Italy. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781509044283. s. 322–326. doi: 10.1109/ICNSC.2017.8000112. Fulltekst i vitenarkiv Vis sammendrag

  In this paper, we propose a digital control system to automatize the operation of a bidirectional front-end for resonating sensors. Due to the simplicity, the control system is power conservative and compact. The main source of power consumption in the bidirectional front-end is the amplifier used to read-out the sensor. Power can be saved by turning off the amplifier after a few periods of the oscillating signal, which is enough to detect the resonant frequency of the sensor. The concept was initially proved by performing simulations in SPICE by using AMS-350nm CMOS technology model. A prototype was realized with discrete components on a PCB and tested with a power supply of 5V. The reading cycle was fixed at 10kHz and a RLC load has been used as model of a MEMS resonant sensor. The values for the RLC components used for the tests are 100Ω, 270pF, 10mH. The nominal power consumption of the front-end without the support of the sleeping mode is 1.7mW while the sleeping mode with reading one oscillation period reduces the power dissipation to 270μW(15.88% of 1.7mW).

• Marchetti, Luca; Berg, Yngvar & Azadmehr, Mehdi (2017). Analysis of the effect of channel leakage on design, characterization and modelling of a high voltage pseudo-floating gate sensor-front-end. Electronics (Basel). 6(4), s. 1–26. doi: 10.3390/electronics6040079. Fulltekst i vitenarkiv Vis sammendrag

  In this paper, we analyze the effects of channel leakage on the design, modelling and characterization of a high voltage pseudo-floating gate amplifier (PFGA) used as sensor front-end. Leakages are known as a major challenge in new modern CMOS technologies, which are used to bias the PFGA, and consequently affect the behavior of the amplifier. As high voltages are desired for actuation of many types of resonating sensors, especially in ultrasound applications, PFGA implemented in high voltage and low leakage technologies, such as older CMOS fabrication processes or power MOSFET can be the only option. The challenge with these technologies used to implement the PFGA is that the leakages are very low, which affect the biasing of the floating gate. However, the numerous advantages of this type of amplifier, implemented with modern fabrication processes, such as high flexibility, compactness, low power consumption , etc. encouraged the authors to research about this topic. This work provides analysis of the working principle and the design rules for this amplifier, emphasizing the major differences between PFGA implemented in low leakage and high leakage technologies. Static and dynamic analysis, input offset and non-linearity of the PFGA are the main topics of this article. Three different design approaches are presented in this paper, in order to provide a more general design procedure and offset compensation for any low leakage PFGA. The amplifier has been simulated in AMS-0.35mm CMOS models for supply voltages of 5 V and 10 V. Two prototypes have been realized to verify the validity of the modelling and the simulation results. Both devices have been realized by using discrete components and mounted on a printed circuit board. In this work, MOSFETs are realized by using commercial IC CD4007UB and 2N7000. Measurement results of the first prototype proved that the implementation of a low leakage PFGA is possible after that the input offset of the amplifier has been compensated. Measurement results of the second prototype have been used to characterize the low leakage PFGA, extracting the best performances from this amplifier, realized with less components and providing a more compact device. Finally, design rules have been summarized in order to implement this amplifier, which enjoys compactness and a relative low power dissipation.

• Azadmehr, Mehdi; Marchetti, Luca & Berg, Yngvar (2017). A low power analog voltage similarity circuit. IEEE International Symposium on Circuits and Systems proceedings. ISSN 0271-4302. doi: 10.1109/ISCAS.2017.8050950. Fulltekst i vitenarkiv Vis sammendrag

  In this paper, we present a low power bump circuit for finding similarity between two voltages. The circuit is based on a voltage correlator that in combination with a differential pair achieves the low power behavior. The circuit has low power consumption and low sensitivity when the different between the two input is large, but as they approach each other the sensitivity increases. The proposed circuit is very simple in design and can have more than 4 orders of magnitude less power consumption than the normal bump circuit.

• Mirmotahari, Omid & Berg, Yngvar (2017). High-Speed Digital Domino Logic for Ultra-Low Supply Voltages. Circuits, systems, and signal processing. ISSN 0278-081X. 36(12), s. 4774–4788. doi: 10.1007/s00034-017-0632-4. Fulltekst i vitenarkiv
• Dadashi, Ali; Mirmotahari, Omid & Berg, Yngvar (2016). NP-Domino, Ultra-Low-Voltage, High-Speed, Dual-Rail, CMOS NOR Gates. Circuits and Systems. ISSN 2153-1285. 7(8), s. 1916–1926. doi: 10.4236/cs.2016.78166. Fulltekst i vitenarkiv
• Dadashi, Ali; Mirmotahari, Omid & Berg, Yngvar (2016). A New Fully Differential Adaptive CMOS Line Driver Using Fuzzy Controller Suitable for ADSL Modems. Circuits and Systems. ISSN 2153-1285. 7(8), s. 1307–1323. doi: 10.4236/cs.2016.78114. Fulltekst i vitenarkiv Vis sammendrag

  In this paper, a new principle for an adaptive line driver using Fuzzy logic is presented. This type of line driver can adapt its output impedance and gain, automatically to the applied load using a fuzzy logic controller (FLC). This results in automatically corrected output impedance for different cables with terminations. Also, the line driver output impedance and gain become insensitive to process and line variations. As an example, a line driver for ADSL application has been designed. The circuit operates from a 3.3 v in a 0.35 um standard CMOS technology. The power consumption of FLC is about 1 mW. The circuit dissipates 106 mW and exhibits a -62 dB THD for a 3.2-Vpp signal at 5 MHz across a 75 ohms Load. It has a relatively high -3 dB bandwidth (240 MHz) with good phase margin of about 67 degrees in a 10 pF load capacitor.

• Mirmotahari, Omid & Berg, Yngvar (2016). Ultra Low-Voltage Static Precharge NAND/NOR Gates. I Ing, Geok (Red.), Proceedings of the 2014 IEEE 5th International Nanoelectronics Conference (INEC). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781467348416. doi: 10.1109/INEC.2014.7460450. Fulltekst i vitenarkiv
• Marchetti, Luca; Berg, Yngvar; Mirmotahari, Omid & Azadmehr, Mehdi (2016). Bidirectional Front-End for Piezoelectric Resonator, 2016 IEEE 13th International Conference on Networking, Sensing, and Control (ICNSC 2016). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781467399753. doi: 10.1109/ICNSC.2016.7479028. Fulltekst i vitenarkiv Vis sammendrag

  This paper presents a bidirectional circuit as front-end for piezoelectric ceramic resonators. The front-end both actives and reads the response of the resonator in different directions and the directionality of the front-end is controlled by swapping the supply rails. Experimental results are obtained by measuring on a semi-discrete board prototype. The resonant frequency of the sensor is 110kHz, the bandwidth of the bidirectional front-end is 1kHz - 500kHz which was implemented by using a CD4007UBE IC. Results show that the system provides an easy and effective way to send an activation signal and to read the response of a piezoelectric resonator.

• Marchetti, Luca; Romi, Amar; Berg, Yngvar; Mirmotahari, Omid & Azadmehr, Mehdi (2016). A discrete implementation of a bidirectional circuit for actuation and read-out of resonating sensors. I Bosio, Alberto (Red.), 2016 11th IEEE International Conference on Design and Technology of Integrated Systems in Nanoscale Era (DTIS). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781509003365. doi: 10.1109/DTIS.2016.7483896. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we propose a simple and compact way to realize a bi-directional interface to drive resonant sensors. The bi-directional interface can be set to both activate the resonating sensor (activation mode) and to read its response (read-out mode). During the normal operation of the system these two modes are activated alternatively, depend on the state of the control signals. The directionality of this device is decided by swapping the power supply rails. The system has been tested using a RLC load, considered as the model for a resonant sensor. Experimental results of a discrete board prototype show the applicability of the interface for resonant load.

• Mirmotahari, Omid; Dadashi, Ali; Azadmehr, Mehdi & Berg, Yngvar (2016). High-speed dynamic dual-rail ultra low voltage static CMOS logic operating at 300 mV. I Bosio, Alberto (Red.), 2016 11th IEEE International Conference on Design and Technology of Integrated Systems in Nanoscale Era (DTIS). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781509003365. doi: 10.1109/DTIS.2016.7483898. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we propose a differential dynamic dual rail CMOS logic style for ultra-low-voltage and high-speed operation. For a supply voltage equal to 300mV using a 90nm TSMC CMOS process the speed of the proposed logic style is more than 25 times faster than traditional dual rail clocked voltage switch logic CVSL

• Mirmotahari, Omid; Dadashi, Ali; Azadmehr, Mehdi & Berg, Yngvar (2015). Novel high-speed dynamic differential ultra low voltage logic for supply-voltage below 300 mV. I Abbas, Mohamad; Chrzanowska-Jesk, M. & El-Kharashi, Watheq (Red.), 2015 IEEE International Conference on Electronics, Circuits, and Systems (ICECS). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781509002467. s. 53–56. doi: 10.1109/ICECS.2015.7440247. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we propose a differential dynamic dual rail CMOS logic style for ultra-low-voltage and high-speed operation. For a supply voltage equal to 300mV using a 90nm TSMC CMOS process the delay of the proposed logic style is reduced more than 96% compared to the delay of dual rail clocked voltage switch logic.

• Dadashi, Ali; Mirmotahari, Omid & Berg, Yngvar (2015). An ultra-low-voltage, semi-floating-gate, domino, dual-rail, NOR gate. I Abbas, Mohamad; Chrzanowska-Jesk, M. & El-Kharashi, Watheq (Red.), 2015 IEEE International Conference on Electronics, Circuits, and Systems (ICECS). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781509002467. s. 61–64. doi: 10.1109/ICECS.2015.7440249. Fulltekst i vitenarkiv
• Berg, Yngvar & Mirmotahari, Omid (2015). Low-voltage and high-speed CMOS circuit design with low-power mode. I Abbas, Mohamad; Chrzanowska-Jesk, M. & El-Kharashi, Watheq (Red.), 2015 IEEE International Conference on Electronics, Circuits, and Systems (ICECS). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781509002467. s. 57–60. doi: 10.1109/ICECS.2015.7440248. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present a modified ultra-lowvoltage and high-speed domino logic style with sleep mode for low-power and low-energy applications. The performance compared to conventional clock voltage switch logic is 15 times higher in terms of speed for a supply voltage equal to 300mV The low-power sleep mode consumes less than 1% of the power in high-performance mode. The CMOS process used for the simulated data presented is 90nm TSMC.

• Azadmehr, Mehdi; Khajeh, Belal & Berg, Yngvar (2015). A New self-sensing approach for actuation and readout of Piezoelectric resonating sensor. I Wang, Chi-Hsu & Huang, Yo-Ping (Red.), ICNSC15, 12th IEEE international Conference on Networking, Sensing and Control. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781467369008. s. 232–235. doi: 10.1109/ICNSC.2015.7116040. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we proposed a new approach to actuate and readout of resonating piezoelectric sensors to realize concept of self-sensing. In the circuit three transistors are used to differentiate between actuation and readout modes. We evaluated a given piezoelectric resonating sensor and the proposed Circuit analytically and with simulations. We also evaluated the applicability of our circuit for mass detection purposes and showed that piezoelectric resonant sensor with our proposed circuit can be a good candidate for mass detection in picogram range.

• Mirmotahari, Omid & Berg, Yngvar (2015). Reliability of High Speed Ultra Low Voltage Differential CMOS Logic. Circuits and Systems. ISSN 2153-1285. 6(5), s. 121–135. doi: 10.4236/cs.2015.65013. Fulltekst i vitenarkiv Vis sammendrag

  In this paper, we present a solution to the ultra low voltage inverter by adding a keeper transistor in order to make the semi-floating-gate more stable and to reduce the current dissipation. Moreover, we also present a differential ULV inverter and elaborate on the reliability and fault tolerance of the gate. The differential ULV gate compared to both a former ULV gate and standard CMOS are given. The results are obtained through Monte-Carlo simulations.

• Berg, Yngvar & Mirmotahari, Omid (2015). Flexible Ultra-Low-Voltage CMOS Circuit Design Applicable for Digital and Analog Circuits Operating below 300mV. I O'Conner, Lisa (Red.), 2015 IEEE Computer Society Annual Symposium on VLSI (ISVLSI). IEEE Press. ISSN 9781479987184. s. 646–651. doi: 10.1109/ISVLSI.2015.83. Fulltekst i vitenarkiv Vis sammendrag

  A generic ultra low-voltage (ULV) CMOS design approach is presented. By applying a floating capacitor to the gate terminal of the enhanced driving transistors, obtained by using a charge injection technique, we may change the ON and OFF currents. The delay in circuits where the enhanced transistors are utilized can be reduced significantly compared to complementary CMOS. The current level of the transistors may be increased for high speed and decreased for low power applications. The design approach may be used to implement ultra low-voltage and high-speed digital logic and Flip-Flops. In addition, the generic technique can be used to implement multiple-valued and analog ultra low-voltage CMOS circuits. For ultra low-voltage digital applications the delay may be reduced to less than 10% compared to static CMOS. The high speed Flip-FLOP presented shows a similar increase in speed compared to conventional Flip-Flops for low supply voltages. For the analog circuit presented the increased current level is used to obtain rail-to-rail operation at higher frequencies than conventional analog circuits.

• Dadashi, Ali; Berg, Yngvar & Mirmotahari, Omid (2015). High-Speed, Modified, Bulk stimulated, Ultra-Low-Voltage, Domino Inveter. I O'Conner, Lisa (Red.), 2015 IEEE Computer Society Annual Symposium on VLSI (ISVLSI). IEEE Press. ISSN 9781479987184. s. 86–90. doi: 10.1109/ISVLSI.2015.100. Fulltekst i vitenarkiv
• Mirmotahari, Omid & Berg, Yngvar (2014). Latching Scheme in Multiple-Valued Recharged Logic. International Journal of Engineering ,Science and Innovative Technology. 3(3), s. 57–72. Fulltekst i vitenarkiv
• Azadmehr, Mehdi; Khajeh, Belal Khakpour & Berg, Yngvar (2014). An ultra-low voltage tunable dual-Band Pass Filter, Multi-Conference on Systems, Signals & Devices (SSD), 2014 11th International. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781479938667. doi: 10.1109/SSD.2014.6808846. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present an ultra-low voltage dual Band Pass Filter with tunable pass bands. The dual band pass filter has two pass bands which can be tuned individually and can operate at supply voltages down to 300mV. The filter is based on Pseudo Floating-Gate and in addition to frequency band adjustment, it offers gain. Both the center frequencies are controlled electronically using bias voltages through the bulk of transistors. The filter benefits from low component spread and compactness, containing only small size transistors and capacitors suited for integration. The simulations presented in this paper are valid for the 90nm CMOS transistor models from STM having a VDD equal to 1.2V and threshold voltage of 250mV.

• Azadmehr, Mehdi; Khajeh, Belal Khakpour & Berg, Yngvar (2014). A bidirectional circuit for actuation and read-out of resonating sensors, 2014 IEEE Faible Tension Faible Consommation (FTFC). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781479937738. doi: 10.1109/FTFC.2014.6828606. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we have demonstrated a novel approach for actuation and read-out of resonating sensors. In this approach, instead of reading the amplitude of the resonating beam in resonance, we use the frequency of the beam as a measure of the sensors response. By using a bidirectional amplifier a pulse is sent to a resonating sensor in one direction and the frequency response of the sensor is measured using the opposite direction of the amplifier. This approach results in more compact and more power conservative systems. This approach mimics the way radars operate where a pulse is sent out and the reflection is measured. The circuit is very compact with low component spread and consumes an average power of 22μW and a maximum power of 100μW when actuating the sensor.

• Azadmehr, Mehdi & Berg, Yngvar (2013). A Bulk-controlled Pseudo-Floating Gate Bandpass Filter. Recent Advances in Electrical Engineering. ISSN 1790-5117. CSCS 13 / ELEL 13, s. 59–63. doi: 10.1109/norchp.2008.4738294. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present a bulk-controlled Pseudo Floating-Gate (BCPFG) Bandpass filter. The filter has a limited Open-Loop gain and linearity for supply voltages down to 600mV . The filter is based on Pseudo Floating-Gate active load amplifier and in addition to gain, it offers frequency band adjustment. Both the low- and high-frequency cutoffs are controlled electronically using bias voltages through the transistor bulks. The BCPFG BP filter enjoys low component spread and compactness, containing only small size transistors and capacitors suited for integration. The simulations presented in this paper are valid for the 90nm CMOS transistor models from STM having a V DD equal to 1.2V and threshold voltage of 250mV.

• Mahmood, Sohail Musa & Berg, Yngvar (2013). Static NP domino Carry gates for Ultra Low Voltage and High Speed Full Adders. North atlantic university union: International Journal of Circuits, Systems and Signal Processing. 7, s. 199–205. Fulltekst i vitenarkiv
• Mahmood, Sohail Musa & Berg, Yngvar (2013). Ultra-low voltage and high speed NP domino carry propagation chain, 2013 IEEE Faible Tension Faible Consommation (FTFC). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781467361057. doi: 10.1109/FTFC.2013.6577759. Fulltekst i vitenarkiv
• Mahmood, Sohail Musa & Berg, Yngvar (2013). High Speed and Ultra Low-voltage CMOS Domino Carry gates. I Said, Agoujil; Tang, Collin Howe Hing & Oprisan, Sorinel (Red.), RECENT ADVANCES in CIRCUITS, COMMUNICATIONS and SIGNAL PROCESSING. World Scientific and Engineering Academy and Society (WSEAS). ISSN 9781618041647. s. 52–57. doi: 10.4236/cs.2016.78166. Fulltekst i vitenarkiv
• Mirmotahari, Omid & Berg, Yngvar (2013). Robust Low-Power CMOS Precharge Logic, 2013 IEEE Faible Tension Faible Consommation (FTFC). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781467361057. s. 11–11. Fulltekst i vitenarkiv
• Mirmotahari, Omid & Berg, Yngvar (2013). Robustness of the Ultra Low-Voltage Domino Gates CMOS. I Privman, V. (Red.), Sixth International Conference on Advances in Circuits, Electronics and Micro-electronics (CENICS 2013). International Academy, Research and Industry Association (IARIA). ISSN 9781612083025. s. 7–12. Fulltekst i vitenarkiv
• Berg, Yngvar (2013). High Speed and Ultra Low-Voltage CMOS Carry Propagation Chain using Floating-Gate Transistors. I Privman, V. (Red.), Sixth International Conference on Advances in Circuits, Electronics and Micro-electronics (CENICS 2013). International Academy, Research and Industry Association (IARIA). ISSN 9781612083025. s. 1–6. doi: 10.1109/ftfc.2013.6577759. Fulltekst i vitenarkiv
• Azadmehr, Mehdi & Berg, Yngvar (2012). An ultra-low voltage pseudo-floating gate amplifier, 2012 Faible Tension Faible Consommation (FTFC). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781467308205. doi: 10.1109/ftfc.2012.6231740. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present an Ultra-Low Voltage Pseudo Floating-Gate Amplifier (ULVPFGA). The amplifier has high gain and high linearity for supply voltages down to 300mV. The amplifier is based on Pseudo Floating-Gate and in addition to gain, it offers frequency band adjustment. Both the low- and highfrequency cutoffs are controlled electronically using bias voltages through their bulk. The ULVPFGA enjoys low component spread and compactness, containing only small size transistors and capacitors suited for integration. We also show a second order section realized using the ULVPFGA. The simulations presented in this paper are valid for the 90nm CMOS transistor models from STM having a VDD equal to 1.2V and threshold voltage of 250mV.

• Berg, Yngvar & Azadmehr, Mehdi (2012). Novel ultra low-voltage and high-speed CMOS pass transistor logic, 2012 Faible Tension Faible Consommation (FTFC). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781467308205. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present a novel CMOS pass transistor logic style for ultra low-voltage and high speed digital applications. The circuits presented offer more than 90% delay reduction compared to conventional CMOS for supply voltages less than 400mV. Differential AND and NAND pass transistor gates presented and compared to complementary pass transistor logic CPL. Simulated data obtained by the Hspice simulation and relevant for 90nm TSMC process are provided.

• Berg, Yngvar & Mirmotahari, Omid (2012). Ultra low-voltage and high speed dynamic and static CMOS precharge logic, 2012 Faible Tension Faible Consommation (FTFC). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781467308205. doi: 10.1109/dtis.2016.7483898. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present novel high speed and ultra low voltage domino invererters. The delay of the inverters are less than 4% of the delay for a standard CMOS inverter. A low power inverter is included and the simulated data for supply voltages in the range of 200mV to 400mV are provoded. Monte carlo simulation show that the ULV logic styles are less influenced by process mismatches than standard CMOS logic. Simulated data presented is obtained by HSpice and process parameters for the 90nm TSMC process.

• Berg, Yngvar & Mirmotahari, Omid (2012). Static Differential Ultra Low-Voltage Domino CMOS logic for High Speed Applications. North atlantic university union: International Journal of Circuits, Systems and Signal Processing. 6(4), s. 269–274. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present a novel static differential ultra low-voltage (ULV) CMOS logic style for High-Speed applications . The proposed logic style is aimed for high speed serial adders in ultra low-voltage applications. The differential ultra low-voltage inverter presented have less than 10% of the delay than standard CMOS inverters for supply voltages less than 500mV . The simulated data presented is obtained using Hspice simulator and applying a 90nm TSMC CMOS process.

• Berg, Yngvar & Azadmehr, Mehdi (2012). Symmetric Autozeroing Floating-Gate Current Mirror, Differential Pair and Transconductance Amplifier for Ultra Low-Voltage Applications. North atlantic university union: International Journal of Circuits, Systems and Signal Processing. 6(4), s. 255–262. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we explore the symmetric autozeroing ultra low-voltage current mirror, differential pair and transconductance amplifier and present some applications. The ultralow transconductance amplifier has a current boost function and resembles switch-cap and auto-zero circuits. The current boost technique have been used to implement ultra-low voltage digital logic. The simulated data presented is relevant for a 90nm TSMC CMOS process.

• Azadmehr, Mehdi & Berg, Yngvar (2012). A band-tunable auto-zeroing amplifier. Recent Advances in Electrical Engineering. ISSN 1790-5117. 3(CSCS 12), s. 24–28. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present a tunable Auto-Zeroing Amplifier(AZA). The amplifier is based on Pseudo Floating gate and in addition to gain, it offers frequency band adjustment. Both the low- and high-frequency cutoffs are controlled electronically using bias voltages, thus the amplifier can be used in design of various time continues filters. The peak gain of the AZA is 22dB dB at 100 MHz and has a bandwidth from. The AZA enjoys low component spread and compactness, containing only small size transistors and capacitors suited for integration. We will also show a second order section realized using the AZA. The simulations presented in this paper are valid for the 90nm CMOS transistor models from STM having a V DD equal to 1.2V and threshold voltage of 0.25V.

• Berg, Yngvar & Mirmotahari, Omid (2012). Novel Static Ultra Low-Voltage and High Speed CMOS Boolean Gates. North atlantic university union: International Journal of Circuits, Systems and Signal Processing. 6(4), s. 249–254. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present robust and high performance static ultra low-voltage CMOS binary logic. The delay of the ultra low-voltage logic presented are less than 10% of the delay of standard CMOS inverters. The logic gates presented are designed using semi floating-gate transistors and a current boost technique. The boolean gates resemble domino CMOS. The performance and robustness of different logic gates are examined and compared to complementary and domino CMOS logic.

• Berg, Yngvar (2012). Ultra Low-Voltage Differential Static D Flip-Flop for High Speed Digital Applications. North atlantic university union: International Journal of Circuits, Systems and Signal Processing. 6(4), s. 263–268. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present an ultra low-voltage and high speed D flip-flop. The flip-flop has an increased current level compared to standard CMOS circuits operating at low supply voltages. The increased current level is obtained by using a synchronized capacitive coupling to a semi floating-gate. The delay of the static differential flip-flop presented is less than 12% compared to conventional differential CMOS flip-flops. The presented circuits have been simulated using Hspice and are valid for 90nm TSMC CMOS process. The proposed high-speed and ultra low-voltage flip-flop can be used for any digital lowvoltage CMOS application.

• Berg, Yngvar & Mirmotahari, Omid (2012). High Speed and Ultra Low-voltage CMOS NAND and NOR domino gates. International Journal of Social, Behavioral, Educational, Economic, Business and Industrial Engineering. ISSN 2010-376X. 68, s. 258–261. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we ultra low-voltage and high speed CMOS domino logic. For supply voltages below 500mV the delay for a ultra low-voltage NAND2 gate is aproximately 10% of a complementary CMOS inverter. Furthermore, the delay variations due to mismatch is much less than for conventional CMOS. Differential domino gates for AND/NAND and OR/NOR operation are presented.

• Berg, Yngvar & Azadmehr, Mehdi (2012). Novel linear autozeroing floating-gate amplifier for ultra low-voltage applications. International Journal of Social, Behavioral, Educational, Economic, Business and Industrial Engineering. ISSN 2010-376X. 68, s. 262–265. Fulltekst i vitenarkiv
• Berg, Yngvar (2012). A novel high speed differential ultra low-voltage CMOS Flip-Flop for high speed applications, CENICS 2012: The Fifth International Conference on Advances in Circuits, Electronics and Microelectronics. International Academy, Research and Industry Association (IARIA). ISSN 9781612082134. s. 11–16. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present a simple ultra low-voltage and high speed D flip-flop. The Flip-Flop may be used in any standard digital low-voltage CMOS applications. Furthermore, the ultra low-voltage Flip-Flop offers reduced data to output delay compared to conventional CMOS Flip-Flops. Different master latch configurations are presented and a differential symmetric ultra low-voltage Flip-Flop is presented. Simulated data using HSpice and process parameters for 90nm CMOS are provided. Preliminary results show that the proposed Flip- Flop has a delay less than 20% compared to a conventional CMOS Flip-Flop.

• Berg, Yngvar & Mirmotahari, Omid (2012). Novel high-speed and ultra-low-voltage CMOS NAND and NOR domino gates, CENICS 2012: The Fifth International Conference on Advances in Circuits, Electronics and Microelectronics. International Academy, Research and Industry Association (IARIA). ISSN 9781612082134. s. 5–10. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present novel ultra-low-voltage and high-speed CMOS NAND and NOR gates. For supply voltages below 500mV the delay for an ultra-low-voltage NAND2 gate is approximately 10% of a complementary CMOS inverter. Furthermore, the delay variations due to mismatch are much lesser than for conventional CMOS. Differential domino gates for AND2/NAND2 and OR2/NOR2 operation are presented. Ultra-low-voltage pass transistors are presented which can be used as latching gates. The ultra-low-voltage gates presented are going to be used for implementation oflow-voltage and high speed adders.

• Mirmotahari, Omid; Berg, Yngvar & Høvin, Mats Erling (2012). Automation of Packing Cell in Fresh Fish Facilities. International Journal of Social, Behavioral, Educational, Economic, Business and Industrial Engineering. ISSN 2010-376X. 68, s. 1956–1961. Fulltekst i vitenarkiv
• Berg, Yngvar (2012). Ultra low-voltage CMOS transconductance amplifiers. Analog Integrated Circuits and Signal Processing. ISSN 0925-1030. 73(3), s. 683–692. doi: 10.1007/s10470-012-9924-6. Fulltekst i vitenarkiv Vis sammendrag

  Simple and symmetrical ultra low-voltage current mode analog circuits and autozeroing amplifiers are presented. The low-voltage analog circuits are based on low-voltage inverters resembling precharge digital logic. Ultra low-voltage analog circuits can be operated at supply voltages down to 250 mV with rail-to-rail input and output swing. The output current of the ultra low-voltage symmetrical transconductance amplifier can be quite large due to a current boost technique. Ultra low-voltage analog circuits can be operated at supply voltages down to 250 mV with rail- to-rail input and output swing. The current headroom is 3 lA and the supply voltage is 300 mV. For supply voltages down to 300 mV simulated data shows that the maximum clock frequency is approximately 600 MHz.

• Berg, Yngvar & Mirmotahari, Omid (2011). Ultra low-voltage CMOS current mirrors. Analog Integrated Circuits and Signal Processing. ISSN 0925-1030. 68(2), s. 219–232. doi: 10.1007/s10470-011-9607-8. Fulltekst i vitenarkiv
• Azadmehr, Mehdi & Berg, Yngvar (2011). A band pass Auto-Zeroing Floating-Gate Amplifier. I Ea, Thomas (Red.), 2011 Faible Tension Faible Consommation (FTFC). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781612846460. s. 83–86. doi: 10.1109/ftfc.2011.5948925. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present a band pass Auto-Zeroing Floating-Gate Amplifier (AZFA). The amplifier is based on Pseudo Floating gate and in addition to gain, it offers frequency band adjustment. Both the low-frequency and high-frequency cutoffs are controlled electronically, thus the amplifier can be used in design of various time continues filters. The AZA enjoys low component spread and compactness, containing only small size transistors and capacitors.

• Berg, Yngvar (2011). Ultra-Low-Voltage and High-Speed CMOS Full Adder Using the Floating Gates and Multiple-Valued Logic, Proceedings of the IEEE Symposium on Multiple-Valued Logic (ISMVL 2011). IEEE (Institute of Electrical and Electronics Engineers). ISSN 9780769544052. s. 259–262. Fulltekst i vitenarkiv
• Berg, Yngvar & Azadmehr, Mehdi (2011). Symmetric autozeroing floating-gate transconductance amplifier for ultra low-voltage applications. I Mladenov, Valeri & Martin, Olga (Red.), Recent researches in circuits, systems, mechanics and transportation systems : Proceedings of the 10th WSEAS International Conference on Circuits, Systems, Electronics, Control & Signal Processing (CSECS '11) : Proceedings of the 7th WSEAS International Conference on Applied and Theoretical Mechanics (MECHANICS '11) : Proceedings ot the 2nd International Conference on Automotive and Transportation Systems (ICAT '11) : Montreux, Switzerland, December 29-31, 2011. World Scientific and Engineering Academy and Society (WSEAS). ISSN 9781618040626. s. 129–133. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we discuss the symmetric autozeroing ultra low-voltage transconductance amplifier and present some applications. The autozeroing performed by all ULV circuits is important to reduce the impact of noise and especially avoid power supply noise in mixed signal low-voltage CMOS circuits. The simulated data presented is relevant for a 90nm TSMC CMOS process

• Berg, Yngvar (2011). ULTRA LOW-VOLTAGE AND HIGH-SPEED CMOS FULL ADDER USING FLOATING-GATES AND MULTIPLE-VALUED LOGIC. Proceedings - International Symposium on Multiple-Value Logic (ISMLV). ISSN 0195-623X. s. 259–262. doi: 10.1109/ISMVL.2011.11. Fulltekst i vitenarkiv
• Berg, Yngvar (2011). NOVEL CLOCKED SEMI-FLOATING-GATE DIFFERENTIAL TRANSCONDUCTANCE AMPLIFER FOR ULTRA-LOW VOLTAGE ANALOG DESIGN. I Mazouffe, Oliver (Red.), Proceedings of the IEEE NEWCAS Conference. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781612841366. s. 285–288. Fulltekst i vitenarkiv
• Berg, Yngvar (2011). NOVEL HIGH SPEED DIFFERENTIAL CMOS FLIP-FLOP FOR ULTRA LOW-VOLTAGE APPICATIONS. I Mazouffe, Oliver (Red.), Proceedings of the IEEE NEWCAS Conference. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781612841366. s. 241–244. Fulltekst i vitenarkiv
• Berg, Yngvar & Mirmotahari, Omid (2011). Novel static differential ultra low-voltage and high speed domino CMOS logic. I Mladenov, Valeri & Martin, Olga (Red.), Recent researches in circuits, systems, mechanics and transportation systems : Proceedings of the 10th WSEAS International Conference on Circuits, Systems, Electronics, Control & Signal Processing (CSECS '11) : Proceedings of the 7th WSEAS International Conference on Applied and Theoretical Mechanics (MECHANICS '11) : Proceedings ot the 2nd International Conference on Automotive and Transportation Systems (ICAT '11) : Montreux, Switzerland, December 29-31, 2011. World Scientific and Engineering Academy and Society (WSEAS). ISSN 9781618040626. s. 138–142. doi: 10.4236/cs.2015.65013. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present a novel static differential ultra low-voltage (ULV) CMOS logic style. Simulated data for the logic style is presented and compared to related ULV logic styles and complementary CMOS gates. The proposed logic style is aimed for high speed serial adders in ultra low-voltage applications. In terms of energy delay product (EDP) the logic style offers a significant improvement compared to complementary CMOS. The proposed differential ULV logic style offers improved noise margin compared to simpler ULV logic styles. The simulated data presented is obtained using Hspice simulator and applying a 90nm TSMC CMOS process.

• Azadmehr, Mehdi & Berg, Yngvar (2011). A bi-directional auto-zeroing floating-gate amplifier. I Mladenov, Valeri & Martin, Olga (Red.), Recent researches in circuits, systems, mechanics and transportation systems : Proceedings of the 10th WSEAS International Conference on Circuits, Systems, Electronics, Control & Signal Processing (CSECS '11) : Proceedings of the 7th WSEAS International Conference on Applied and Theoretical Mechanics (MECHANICS '11) : Proceedings ot the 2nd International Conference on Automotive and Transportation Systems (ICAT '11) : Montreux, Switzerland, December 29-31, 2011. World Scientific and Engineering Academy and Society (WSEAS). ISSN 9781618040626. s. 70–75. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present a bi-directional Auto-Zeroing Floating-gate Amplifier(AZFA). Due to gain and possibility of frequency band adjustment in both directions, the circuit is suited for designing bi-directional analog filters and amplifiers. The amplifier has different properties in each direction regarding frequency band and gain. The operation direction is controlled by swapping the V DD and GND. The AZFA enjoys low component spread and compactness, containing only minimum size transistors and capacitors. These properties in addition to bi-directionality of the circuit can result in more compact systems.

• Berg, Yngvar & Mirmotahari, Omid (2011). Static ultra low-voltage and high performance CMOS NAND and NOR gates. I Mladenov, Valeri & Martin, Olga (Red.), Recent researches in circuits, systems, mechanics and transportation systems : Proceedings of the 10th WSEAS International Conference on Circuits, Systems, Electronics, Control & Signal Processing (CSECS '11) : Proceedings of the 7th WSEAS International Conference on Applied and Theoretical Mechanics (MECHANICS '11) : Proceedings ot the 2nd International Conference on Automotive and Transportation Systems (ICAT '11) : Montreux, Switzerland, December 29-31, 2011. World Scientific and Engineering Academy and Society (WSEAS). ISSN 9781618040626. s. 143–146. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we examine the robustness and performance of static ultra low-voltage CMOS binary logic. The logic gates presented are designed using semi floating-gate transistors and resembles domino CMOS. The performance and robustness of different logic gates are examined and compared to complementary and domino CMOS logic.

• Berg, Yngvar (2011). Differential static ultra low-voltage CMOS flip-flop for high speed applications. I Mladenov, Valeri & Martin, Olga (Red.), Recent researches in circuits, systems, mechanics and transportation systems : Proceedings of the 10th WSEAS International Conference on Circuits, Systems, Electronics, Control & Signal Processing (CSECS '11) : Proceedings of the 7th WSEAS International Conference on Applied and Theoretical Mechanics (MECHANICS '11) : Proceedings ot the 2nd International Conference on Automotive and Transportation Systems (ICAT '11) : Montreux, Switzerland, December 29-31, 2011. World Scientific and Engineering Academy and Society (WSEAS). ISSN 9781618040626. s. 134–137. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present a simple ultra low-voltage and high speed D flip-flop. The delay of the static differential flip-flop presented is less than 12% compared to conventional differential CMOS flip-flops. The presented circuits have been simulated using Hspice and are valid for 90nm TSMC CMOS process. The proposed high-speed and ultra low-voltage flip-flop can be used for any digital low-voltage CMOS application.

• Azadmehr, Mehdi & Berg, Yngvar (2011). Current-starved pseudo floating-gate filters. I Kanoun, Olfa (Red.), Transactions on systems, signals and devices : issues on sensors, circuits & instrumentation. Shaker Verlag. ISSN 9783844006780. s. 381–399. doi: 10.1109/ssd.2009.4956753. Fulltekst i vitenarkiv Vis sammendrag

  In this paper we present different types of active filters designed using analog Current-Starved Pseudo Floating-Gate (CSPFG) inverters. We show how all types of filters (low pass, high pass, band pass and band reject) can be designed using only a combination of capacitors and CSPFG inverters, resulting in areasaving circuits suited for VLSI and ULSI circuit design. All the filters presented are tunable, allowing band adjustment using a bias voltage. Typical applications are detection of high frequency components in sensory signals and in radio frequency signal processing. AC simulations of the circuits are presented to show that these circuits are suited for high performance filter design. In addition, the open-loop gain of the CSPFG inverter is examined.

• Moradi, Farshad; Wisland, Dag T; Berg, Yngvar; Aunet, Snorre & Cao, Tuan Vu (2010). Process Variations in Sub-Threshold SRAM Cells in 65nm CMOS. I Alioto, Massimo (Red.), Proceedings of the 22nd International Conference on Microelectronics. IEEE (Institute of Electrical and Electronics Engineers). ISSN 9781424481569. Fulltekst i vitenarkiv

Se alle arbeider i NVA

• Mirmotahari, Omid; Berg, Yngvar; Grun, Helene Nordrum & Grønland, Lise Katarina (2023). Gamification - Er spill bare for underholdning eller er det fremtidens læringsverktøy? Fulltekst i vitenarkiv
• Dadashi, Ali; Berg, Yngvar & Mirmotahari, Omid (2017). Fast-settling, energy-efficient, amplifier for high-resolution LCD displays. Fulltekst i vitenarkiv
• Marchetti, Luca; Mirmotahari, Omid; Berg, Yngvar & Azadmehr, Mehdi (2016). A discrete implementation of a bidirectional circuit for actuation and read-out of resonating sensors. Fulltekst i vitenarkiv
• Marchetti, Luca; Mirmotahari, Omid; Berg, Yngvar & Azadmehr, Mehdi (2016). Bidirectional front-end for piezoelectric resonator. Fulltekst i vitenarkiv
• Dadashi, Ali; Mirmotahari, Omid & Berg, Yngvar (2016). Domino Dual­Rail, High­Speed, NOR Logic, with 300mV supply in 90 nm CMOS Technology. Fulltekst i vitenarkiv
• Mirmotahari, Omid; Dadashi, Ali & Berg, Yngvar (2016). High-speed dynamic dual-rail ultra low voltage static CMOS logic operating at 300 mV. Fulltekst i vitenarkiv
• Dadashi, Ali; Berg, Yngvar & Mirmotahari, Omid (2016). A High-Performance CMOS Modified Amplifier. Fulltekst i vitenarkiv
• Dadashi, Ali; Mirmotahari, Omid & Berg, Yngvar (2015). Ultra-Low-Voltage, Semi-Floating-Gate, Domino, Dual-Rail, Nor Gate. Fulltekst i vitenarkiv
• Azadmehr, Mehdi & Berg, Yngvar (2011). A band pass Auto-Zeroing Floating-Gate Amplifier. Fulltekst i vitenarkiv
• Moradi, Farshad; Wisland, Dag T; Aunet, Snorre & Berg, Yngvar (2011). Ultra Low Power Digital Circuit Design for Wireless Sensor Network Applications. Universitetet i Oslo. Fulltekst i vitenarkiv Vis sammendrag

  Ny forskning innenfor feltet trådløse sensornettverk åpner for nye og innovative produkter og løsninger. Biomedisinske anvendelser er blant områdene med størst potensial og det investeres i dag betydelige beløp for å bruke denne teknologien for å gjøre medisinsk diagnostikk mer effektiv samtidig som man åpner for fjerndiagnostikk basert på trådløse sensornoder integrert i et ”helsenett”. Målet er å forbedre tjenestekvalitet og redusere kostnader samtidig som brukerne skal oppleve forbedret livskvalitet som følge av økt trygghet og mulighet for å tilbringe mest mulig tid i eget hjem og unngå unødvendige sykehusbesøk og innleggelser. For å gjøre dette til en realitet er man avhengige av sensorelektronikk som bruker minst mulig energi slik at man oppnår tilstrekkelig batterilevetid selv med veldig små batterier. I sin avhandling ” Ultra Low power Digital Circuit Design for Wireless Sensor Network Applications” har PhD-kandidat Farshad Moradi fokusert på nye løsninger innenfor konstruksjon av energigjerrig digital kretselektronikk. Avhandlingen presenterer nye løsninger både innenfor aritmetiske og kombinatoriske kretser, samtidig som den studerer nye statiske minneelementer (SRAM) og alternative minnearkitekturer. Den ser også på utfordringene som oppstår når silisiumteknologien nedskaleres i takt med mikroprosessorutviklingen og foreslår løsninger som bidrar til å gjøre kretsløsninger mer robuste og skalerbare i forhold til denne utviklingen. De viktigste konklusjonene av arbeidet er at man ved å introdusere nye konstruksjonsteknikker både er i stand til å redusere energiforbruket samtidig som robusthet og teknologiskalerbarhet øker. Forskningen har vært utført i samarbeid med Purdue University og vært finansiert av Norges Forskningsråd gjennom FRINATprosjektet ”Micropower Sensor Interface in Nanometer CMOS Technology”.

Se alle arbeider i NVA